If you’ve got a Samsung TV with no visible screws on the back, you’re not losing it - these are known as screwless Samsung TVs, and they use internal clips instead of screws to hold the rear panel in place. Removing the back might seem intimidating at first, but with the right tools and a little patience, you can do it yourself - no repair shop required. 💪
At TVpartsToday, we’re big fans of empowering DIYers with the knowledge and parts they need. So let’s walk through the process together!
Would you rather watch a video instead? Check out our helpful YouTube video below:
🧰 What You’ll Need
-
✅ Plastic prying tool (spudger or anything similar that is non-metallic)
-
✅ Soft surface or towel (to protect the screen)
-
✅ Optional helper (especially helpful for TVs 60” or larger)
-
🚫 No metal tools! (They can crack the frame or scratch your TV)
📺 Step-by-Step: Removing the Back Panel
1. Unplug the TV
Always, always unplug your TV before opening it. Safety first! ⚡
2. Lay the TV Face Down
Place it gently face-down on a soft, flat surface like a bed, couch, or towel-covered table. This protects the screen while you work.
TVpartsToday Tip:
Make sure the surface is firm enough to support the TV but soft enough to avoid pressure marks on the screen.
3. Find the Seams
Run your hand around the edge of the TV. You’ll feel a small gap between the front bezel and back panel. This is where you’ll insert your pry tool.
4. Use a Plastic Pry Tool to Pop Clips
Start at a bottom corner or flexible side edge. Insert the plastic tool gently into the seam and twist or slide it slightly to pop open the internal clips. You’ll hear small clicking or popping sounds as each clip disengages - don’t worry, that’s normal. 🔧
TVpartsToday Tip:
🚫 Avoid using a screwdriver or any metal tool - they can easily damage the plastic housing or even slip and harm internal components.
5. Work Your Way Around
Once the first few clips are loose, move around the entire perimeter of the TV, releasing one clip at a time. Don’t force anything! These clips are snug by design but will release with enough even pressure.
Be patient! Rushing this step is the #1 reason for cracked bezels.
6. Lift the Back Panel Off
Once all clips are released, gently lift off the back panel. If it feels stuck, recheck the perimeter - there may be a few stubborn clips still holding on.
And voilà - you’re in! Now you have full access to your main board, power board, T-Con board, and more.
🧠 Why DIY?
Screwless Samsung TVs are perfect candidates for DIY repair. You don’t need special tools or advanced knowledge - just the right guide (that's us!) and the right parts.
If your Samsung TV is experiencing issues like no power, no display, or boot looping, chances are high that replacing the main board or power supply board can fix the issue. Why pay hundreds for a repair shop when you can do it yourself for a fraction of the cost?
TVpartsToday Tip:
🧩 Once you’ve got the back off, take note of the part numbers printed on the boards. Then head to TVpartsToday.com to find exact replacements. If you’re not sure what part to order, just give us a shout!
💬 Final Thoughts
Samsung screwless TVs are sleek on the outside, but once you know how to open them up, they’re surprisingly simple to work on. Whether you're swapping out a faulty main board or troubleshooting a power issue, DIY repair can save you time and money—and give you the satisfaction of fixing it yourself. 🛠️
So go ahead, crack that case (carefully!), and let TVpartsToday be your guide to a fully working TV. 💡
💬 Need Help?
If you’re still unsure about the issue or need to replace a part, reach out to TVpartsToday. We can help you identify the exact cause of the problem and provide the right replacement part!
Would you rather watch a video? Check out our helpful Troubleshooting 101 playlist over on YouTube!
Would you rather chat with a seasoned repair expert? Head on over to our TVRepairHelp subReddit!
📦 Need help finding the right board or part?
📞 Call us at 930-212-1975 or browse our inventory online.
🛠️ DIY-friendly parts, fast shipping, and expert support – only at TVpartsToday.
1 comment
very helpful